Cover for Jon Boat: How to Choose, Measure and Fit One (2026)
Learn how to choose the right cover for jon boat, measure it correctly and fit it snugly so rain, sun and debris stay out. Practical steps for every size.
Updated November 2026
A well-fitted cover for jon boat keeps rain, sun, leaves and debris off your hull and seats between trips. This guide walks you through measuring your boat, picking the right material and fit style, and securing the cover so it stays put in wind. Most of the work is in the measuring, so take your time there.
Measure Your Jon Boat Before You Shop
Jon boats are usually sold by length, but length alone won’t get you a good fit. Covers are sized to the boat’s overall length and beam, and the height of the highest point matters too. Take these measurements on a flat surface:
Shopping for one? See our guide: 3 Best 14ft Jon Boat Covers for Every Need (2026).
- Overall length, bow tip to stern transom, not the hull’s waterline length.
- Beam, the widest point across the gunwales.
- Height, from the ground to the top of the tallest part (usually the console or a raised seat).
- Bow and stern shape. A pointed bow needs a different cut than a square one.
Add a few inches to length and beam to allow for fabric. Manufacturers typically specify their own size charts, so compare your numbers against the chart rather than assuming a “14 foot” label matches your boat.
Choose the Right Material and Fit Style
Most cover materials fall into two groups: woven polyester or polyethylene for general use, and heavier coated fabrics for long-term outdoor storage. Look for UV-resistant coatings, since sun is what breaks down fabric fastest. Breathable panels or vents reduce trapped moisture and mildew.
Fit style matters as much as material:
| Fit style | Best for | Trade-off |
|---|---|---|
| Custom-cut | Boats with a consistent shape | Less forgiving if your measurements are off |
| Universal (sized range) | Common jon boat sizes | More fabric to manage in wind |
| Trailer-style | Boats stored on a trailer | Must be sized to include the trailer frame |
Fit and Secure the Cover
Once you have the cover, fitting it is a short process if you do it in the right order:
- Dry the hull and seats completely. Trapped water causes mildew under the fabric.
- Center the cover from bow to stern, then pull the sides down evenly.
- Fasten the straps or buckles under the hull first, then the bow and stern tie-downs.
- Tighten the cover enough that it doesn’t flap, but leave a little slack so rain runs off instead of pooling.
- Check the cover after the first strong wind and retighten any loose straps.
If your boat has a tiller or outboard, cut or use a cover designed with a motor flap so the fabric doesn’t rub against the engine.
Common Mistakes to Avoid
- Buying by length only and ignoring beam or height.
- Covering a wet boat, which traps moisture and encourages rot in wood or mildew on vinyl.
- Leaving the cover loose so wind lifts it and wears the fabric at the edges.
- Skipping vents or breathable panels in humid climates.
- Storing the cover folded wet, which speeds up mildew and staining.
Recommended Gear
- Heavy-duty tie-down straps help keep the cover secured in wind. View on Amazon
- Cover-safe cleaning brush lets you remove leaves and debris without scratching the fabric. View on Amazon
- Boat cover repair patch kit handles small tears before they spread. View on Amazon
FAQ
How do I know which size cover for jon boat I need?
Measure overall length, beam and the height of the tallest point, then compare those numbers to the manufacturer’s size chart. Add a few inches to length and beam for fabric clearance.
Can I leave a cover on a jon boat all year?
You can, but only if the cover is UV-resistant, breathable and the boat is dry before covering. Check the cover periodically for loose spots and mildew.
Do I need a boat cover for jon boat storage on a trailer?
A trailer-style cover is helpful if the boat stays on the trailer, because it accounts for the frame. Confirm the sizing includes the trailer before you buy.
Conclusion
Measure carefully, choose a material and fit style that suit your climate, and secure the cover snugly after the boat is dry. Check your straps after the first windy day and you’ll avoid most common problems. A good cover for jon boat storage pays off in fewer repairs and a longer-lasting hull.
Related reading
- Top 3 Covers for 14 Ft Jon Boat Picks Compared in 2026
- Jon Boat Cover 18ft: How to Measure, Choose and Fit One (2026)
- Jon Boat Cover 14: How to Measure, Choose and Fit One (2026)
- Jon Boat Cover 12 Ft: How to Measure, Choose and Fit One (7 Steps)
- 4 Best 16 Foot Jon Boat Covers for Every Need (2026)
- 12ft Jon Boat Cover: How to Measure, Choose and Fit One Correctly
Ready to choose one?
