Tri Hull Boat Cover: How to Measure, Choose and Fit One (2026)
Learn how to choose a tri hull boat cover, measure your hull and fit it so it sheds water, resists wind and lasts through the season.
Updated November 2026
A tri hull boat cover protects a three-point hull from sun, rain, debris and wind when the boat is stored. To get a good fit, you need accurate measurements of the hull’s length, beam and height, a cover material suited to your climate, and a secure way to tension it. This guide walks through each step so the cover sheds water instead of pooling on top of your boat.
Step 1: Measure Your Tri Hull Accurately
Tri hull boats have a flatter bottom with a pronounced V-shaped bow, so the cover must follow those lines without gapping. Measure the overall length from the tip of the bow to the stern, then measure the beam at the widest point. Finally, measure the height from the deck to the top of the windshield or console, and note the height of any T-top or bimini frame.
Shopping for one? See our guide: Seal Skin Boat Cover Review: Is It Worth It? (2026).
Manufacturers usually list covers by length and beam ranges, and many ask for a measurement of the trailer tongue to stern. Always check the size chart against your numbers, and round up rather than down. A cover that is slightly too large can be cinched; one that is too small will tear at the seams.
Step 2: Choose the Right Material and Fit Style
Most tri hull covers use coated polyester or solution-dyed acrylic. Coated polyester resists water well and is common in budget and mid-range options. Solution-dyed acrylic holds its color longer under UV exposure and breathes a little better, which helps reduce trapped condensation.
Decide between a standard cover and a custom-fit cover. Standard covers are quicker to install but can flap in wind. Custom covers cost more to buy but hold a tighter shape, which is useful if you store the boat outdoors year-round. For a broader look at the options, see Worlds Best Boat Cover: How to Choose the Right One for Your Boat (2026).
Step 3: Install and Secure the Cover
- Clean the hull and deck, and remove loose items such as fishing rods, cushions and electronics that could scratch the cover.
- Drape the cover from the bow, centering the front seam over the bow eye.
- Pull the cover back toward the stern and align the side seams with the gunwales.
- Fasten the bow tie-down and the stern straps to the trailer frame or a dock cleat.
- Tighten the underside straps or cinch cords so the cover sits snug without stretching.
- Check for low spots where water could collect, and add a support pole or adjust the strap tension if needed.
If your boat has a T-top, the cover will need a separate frame cover or a cover designed for T-top use. Tri hull hulls often have a small rise at the bow that can hold water, so make sure the front panel is tight.
Step 4: Provide Ventilation and Maintain the Cover
Trapped moisture is the main cause of mildew inside covered boats. Install vent grommets or zippered vents on the upper panels, and keep them clear of leaves and dirt. Rinse the cover with fresh water every few weeks during storage and let it dry completely before folding it for the season. The guide on Waterproofing a Boat Cover: A Step-by-Step Guide for Beginners explains how to maintain water resistance over time.
Common Mistakes
- Measuring only the length and ignoring beam and height.
- Leaving the cover loose, which lets wind lift and abrade it.
- Storing the cover wet, which encourages mildew and weakens the coating.
- Covering a boat that still holds rainwater or melted snow in the bilge.
- Skipping the tie-downs in exposed areas.
Recommended Gear
A sturdy set of tie-down straps helps keep a tri hull cover from shifting in wind. Look for ratchet or cam-buckle straps with UV-resistant webbing. View on Amazon
A cover support pole or adjustable frame prevents water from pooling on the bow and stern. View on Amazon
Vent grommets and replacement cover fasteners are easy to install and extend the life of the cover. View on Amazon
FAQ
How do I know what size tri hull boat cover to buy?
Measure the overall length, the beam at its widest point and the height over the highest point of the console or T-top. Match those numbers to the manufacturer’s size chart and choose the next size up if you fall between two sizes.
Can I leave a tri hull boat cover on all year?
You can, but only if the cover is well ventilated and kept clean and dry. Remove it periodically to inspect the hull and the cover, and check with the manufacturer for recommended use duration.
Why does my cover keep collecting water?
Water usually pools where the cover sags, most often at the bow or over a console. Add a support pole, adjust the strap tension, or check that the cover is sized correctly for the hull.
Conclusion
A well-fitted tri hull boat cover starts with accurate measurements and the right material for your storage conditions. Secure it with tight tie-downs, vent it to prevent mildew, and inspect it regularly. Consult a marine professional if you have questions about your specific hull or storage location.
Related reading
Ready to choose one?
