We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Put a Boat Cover On: A Step-by-Step Guide for Beginners

Learn how to put a boat cover on correctly, with step-by-step fitting, tension and securing tips that keep water out and the cover in place.

Updated November 2026

Knowing how to put a boat cover on correctly keeps water, leaves and UV damage off your boat and stops the cover from flapping or pooling with rain. This guide walks through preparing the boat, positioning the cover, setting the fit and securing it so it stays put through wind and weather. The process takes most people under an hour with two sets of hands.

Prepare the Boat and the Cover

Start with a clean, dry boat. Rinse off dirt and debris, then let the deck and any exposed hardware dry fully. Trapped moisture under a cover can encourage mildew on vinyl and canvas. Remove loose items such as fishing rods, cushions and electronics that could snag the fabric.

Shopping for one? See our guide: Seal Skin Boat Cover Review: Is It Worth It? (2026).

Next, lay the cover out flat on a clean surface, such as a driveway or tarp, so you can see the front, back and sides. Check the labeling if your cover has one, and confirm the orientation. Most covers have a designated bow end, which should face forward.

Position and Drape the Cover

Lift the cover by its front edge and have a helper hold the rear. Work from the bow toward the stern, draping the fabric evenly over the top of the boat. Keep the cover centered so the overhang on each side is roughly equal. If the boat has a windshield or T-top, pass the cover over it carefully to avoid stretching the frame.

Once the cover is on, walk around the boat and check that the hem sits level all the way around. Gaps at the bottom let wind lift the cover, so adjust until the skirt rests evenly against the hull.

Set the Fit and Secure the Cover

Fasten the cover according to its design. Common methods include:

  • Buckling the straps under the hull at each marked point.
  • Snapping the skirt to the hull or trailer.
  • Tying the bow and stern lines to a dock cleat or trailer tie-down.
  • Setting support poles or bars inside the cover to lift the fabric off the boat.

Tighten each strap until the cover feels firm without pulling hard on the seams. Overtightening can tear grommets and stress stitching. Check the tension again after a day or two, since fabric can settle.

Work With Wind and Water

Fold or tuck loose edges so they don’t catch wind. Make sure the cover doesn’t sit in a pocket where rain collects. A slight slope toward the edges lets water run off instead of pooling on the top.

Common Mistakes to Avoid

  • Covering a wet boat, which traps moisture and invites mildew.
  • Dragging the cover across the deck, which can scuff gelcoat and abrade the fabric.
  • Skipping the hull straps, leaving the cover to blow loose in strong wind.
  • Leaving the cover tight against a windshield or antenna with no slack, which strains the frame.
  • Ignoring the hem, which lets rain and debris blow underneath.

A set of support poles or bars helps keep the fabric from sagging and collecting water. View on Amazon

Extra stainless straps or a tie-down kit give you more securing options in high wind. View on Amazon

FAQ

Do I need two people to put a boat cover on?

One person can manage smaller boats, but two people make it far easier on larger hulls. A helper keeps the cover from dragging and lets you position it evenly.

How tight should a boat cover be?

It should feel snug and firm with no loose flapping, but not so tight that seams or grommets are strained. Recheck the tension after the first few days.

Can I leave a boat cover on all winter?

Many owners do, provided the boat is clean and dry, the cover is securely fastened and any snow is cleared off periodically. Check the manufacturer’s guidance for your specific cover and climate. For questions about storing a boat over winter, consult a marine professional.

Conclusion

Putting a boat cover on is mostly about a clean start, even draping and secure fastening. Take the time to check the hem, tension and drainage, and the cover will protect your boat for seasons to come. Check your cover’s care guidance each year, too.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our houseboating guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Discover Houseboating.