16 Foot Bass Tracker Boat Cover: How to Choose, Measure and Fit One (2026)
Learn how to choose, measure and fit a 16 foot bass tracker boat cover, with steps for sizing, materials, tie-downs and care to protect your boat year-round.
Updated November 2026
A 16 foot bass tracker boat cover protects your hull, console, seats and electronics from sun, rain, debris and dew when the boat is parked. To get the right one, you need to measure the boat correctly, pick a fabric suited to your storage conditions, confirm the cover has the right fit features for a bass tracker’s open deck and tiller or console layout, and secure it so wind cannot pull it loose. This guide walks through each step in order.
Why a Bass Tracker Needs a Cover Built for Its Shape
Bass trackers are aluminum or fiberglass boats with a flat, open deck, a bow casting platform, and often a console or side console with a windshield. That shape creates problems a generic cover does not solve well. Flat decks collect standing water. Casting decks and rod holders create pinch points. Trolling motors, bow-mounted electronics and rod lockers all need clearance. A cover cut for a 16 foot bass tracker will usually have bow and stern tie points, a center ridge or cross-seam to shed water, and enough height to clear a console.
Shopping for one? See our guide: 4 Best Boat Covers for Bass Tracker Models for Every Need (2026).
If you already keep a cover on another boat, don’t assume it will work. A 16 foot pontoon, jon boat or center console has a different profile. For a comparison of how fit and features change between boat types, see Boat Cover 16 Foot: How to Choose, Fit and Care for One (Step-by-Step) and 4 Best 16 Foot Jon Boat Covers for Every Need (2026).
Step 1: Measure Your 16 Foot Bass Tracker Correctly
Most covers are sized by overall length and beam, but manufacturers also specify height, bow and stern dimensions, and whether the cover is sized for a console or a tiller. Measure before you shop, and measure with the boat in the position it will be stored in.
- Overall length: Measure from the tip of the bow (including any bow eye or fixed trolling motor mount you want covered) to the rearmost point of the transom, with a tape running along the gunwale. Record the number in feet and inches.
- Beam: Measure the widest point across the gunwales, outside edge to outside edge, usually at the seats or console.
- Height: Measure from the deck to the highest point you want covered. Include a console windshield, T-top, or raised poles if you have them. Trackers with a bimini or a tall console often need a cover with a higher peak.
- Trailer and motor: Note whether the outboard will be covered (most cover designs include a motor cover or a separate motor hood) and whether the trailer tongue needs clearance.
- Trolling motor and bow mount: Measure the trolling motor shaft height and the bow mount’s footprint so the cover can be cut with a pocket or relief rather than being forced down on top of them.
What to Do With the Numbers
Compare your measurements against the manufacturer’s size chart, not just the advertised boat length. Many 16 foot bass tracker covers are sized for a range (for example, a length band plus a beam range). If your beam sits near the top or bottom of a band, choose the size that fits your widest point and let the manufacturer’s tie-downs handle the rest. Covers that are too loose will flap and chafe. Covers that are too tight will split at seams or stress the zippers.
Step 2: Choose a Fabric and Construction for Your Storage Conditions
The fabric determines how well the cover sheds water, how long it lasts in sun, and whether it breathes. Solution-dyed polyester and marine-grade vinyl-coated polyester are common choices for boat covers. Breathable fabrics help reduce condensation, which matters in humid climates or if you store the boat under a roof with poor airflow.
| Storage situation | What to look for | Why it matters |
|---|---|---|
| Outdoor, full sun year-round | UV-treated, solution-dyed fabric; reinforced seams | Sun breaks down untreated fabric and thread quickly. |
| Outdoor, heavy rain or snow | Water-resistant top layer; sloped or ridged top; sturdy tie-downs | Standing water and snow loads stretch covers and cause sagging. |
| Humid area or covered storage | Breathable fabric; vents or mesh panels | Trapped moisture leads to mildew and corrosion on metal parts. |
| Frequent wind exposure | Strap points at bow, stern and sides; grommets with backing plates | Wind lifts loose covers and tears grommets. |
For a deeper look at how fabric affects water resistance, see Waterproof Boat Cover Material: Which Fabric Keeps Water Out Best? and Waterproof Pontoon Boat Cover: How to Choose, Fit and Keep It Dry (2026).
Ventilation Matters More Than Many Owners Expect
A fully sealed cover can trap warm, moist air under the fabric. Owners often report mildew smell, damp carpet and foggy windshields when a cover has no vents. Look for a cover with two or more mesh or zippered vents, placed near the bow and stern. If your cover has no vents, plan to open one end on mild, dry days.
Step 3: Confirm the Fit Features That a Bass Tracker Needs
Once you narrow your size and fabric, check these features before you buy:
- Bow and stern tie-downs: Confirm the cover has strap points or bungee loops at the bow eye and transom corners.
- Console or windshield pocket: If your boat has a windshield, check whether the cover includes a pocket or a raised section to clear it.
- Motor cover or motor hood: Decide whether you want the outboard covered by the same cover. Some owners prefer a separate motor cover for easier removal.
- Rod and electronics clearance: A cover pressing on rod tips or a bow-mount transducer can break parts. Look for cutouts or a higher profile over the bow.
- Trailer-side straps: Side straps that run under the trailer or connect to trailer tie points keep the cover from lifting in wind.
Step 4: Install the Cover Without Damaging Your Boat
Install the cover on a dry, calm day. Working alone is possible, but two people make the job faster and reduce the chance of dragging fabric across sharp edges.
- Clean and dry the deck, console and gunwales. Grit under the cover will scratch gel coat and finish.
- Remove loose items such as rods in the open, fish finder mounts you don’t want rubbing, and anything sharp on the bow.
- Lay the cover over the bow first, then draw it back over the console and seats. Keep the front of the cover centered.
- Fasten the bow and stern tie-downs snug but not tight. The cover should sit flat with no large wrinkles or sagging pockets.
- Connect side straps under the gunwales or to the trailer. If you tow the boat, check that straps clear the wheels, bunks and lights.
- Check the fit after a few hours of wind. Retighten any strap that has loosened.
Tools and Supplies You May Need
- Soft brush or cloth for cleaning the deck before installation
- Extra bungee cords or cover straps if the included set is short
- Foam or padding for sharp edges on the bow eye or rod holders
- A small tape measure for re-checking fit after washing (fabric can shift slightly)
Step 5: Maintain the Cover and the Boat Under It
A cover only protects the boat if it stays clean, dry and intact. Rinse the cover with fresh water every few weeks in dusty or pollen-heavy areas, and clean it with a mild soap recommended by the manufacturer. Avoid pressure washers, which can strip water-repellent coatings and damage seams. Let the cover dry fully before folding or storing it.
Check the cover each month for torn grommets, worn stitching and thinning fabric in the sun zones over the bow and console. Replace tie-down straps that have stretched or cracked. Keep the cover off the boat when you are not using it for long stretches if you live where snow or ice builds up, and never store the boat under a cover with standing water on top.
Common Mistakes
- Buying by length only. Beam, height and console shape matter just as much.
- Ignoring vents. A sealed cover in a humid spot often causes more damage than a cover without any protection.
- Over-tightening. Tie-downs pulled hard stress seams and can crack the gunwale finish.
- Leaving rods or sharp gear touching the fabric. Abrasion wears through the cover over time.
- Installing on a wet or dirty deck. Trapped grit scratches the finish.
- Skipping post-storm checks. A loose strap after a windy night can turn into a torn cover by morning.
Recommended gear
- Extra cover straps or bungee cords: A longer strap set helps when the included tie-downs don’t reach a cleat, trailer tie point or bow eye. View on Amazon
- Protective foam edge guard: Foam tubing on bow eyes and rod tips prevents the fabric from chafing on hardware. View on Amazon
- Mild marine fabric cleaner: A cleaner made for vinyl and synthetic boat covers helps remove mildew without stripping water repellency. View on Amazon
FAQ
What size cover does a 16 foot bass tracker need?
Measure the overall length, beam and height of your boat, then match those numbers to the manufacturer’s size chart. Choose the size that fits the beam and height you measured, since those dimensions determine whether the cover sits flat and clears the console.
Should I cover the outboard motor too?
It depends on your storage and how often you use the boat. A motor cover or hood keeps dust and rain off the engine. If you use a separate motor cover, make sure it doesn’t stress the main cover’s tie-downs.
Are breathable covers better than waterproof ones?
Breathable fabrics reduce trapped moisture, which helps in humid conditions. Waterproof fabrics shed rain more effectively. Many quality covers combine water-resistant fabric with vents so you get both protection and airflow.
How long does a boat cover last?
Lifespan depends on fabric quality, sun exposure and how well you maintain it. Many owners report several seasons of use from a well-made cover in moderate climates, while cover in intense sun may wear faster. Inspect it regularly and replace it when seams, grommets or fabric show significant wear.
Can I use a cover on a trailer while driving?
Not recommended. A cover should be removed before towing unless the manufacturer specifically approves it. Wind at highway speeds can tear the cover and strain tie-downs.
How do I stop water pooling on top of the cover?
Choose a cover with a ridged or sloped top and make sure it is pulled taut. Some covers include a center cross-seam designed to shed water. Brush off snow and debris after storms to reduce load.
Do I need to remove the cover to wash the boat?
You can wash the boat while covered only if you lift the cover to a clean area. Otherwise, remove the cover, wash the boat and deck, let everything dry, then reinstall the cover.
Should I consult a professional about cover installation or sizing?
If your boat has nonstandard modifications, a custom console, or a damaged hull, ask a marine dealer or upholsterer for advice before ordering a cover. They can check clearances and recommend fit adjustments.
Conclusion
A well-fitted 16 foot bass tracker boat cover is one of the simplest ways to protect your investment in the boat. Measure carefully, choose fabric and vents for your local weather, confirm the bow, console and tie-down features, and check the fit after every big wind. A little attention to installation and maintenance will keep the boat dry and the cover working for many seasons.
Related reading
Ready to choose one?
