Boat Trailer Fenders 13 Inch Wheels: How to Choose and Fit Them
Boat trailer fenders 13 inch wheels need the right width, clearance and mounting. Learn how to measure, choose and fit them so your trailer stays protected.
Updated November 2026
Boat trailer fenders for 13 inch wheels need to clear the tire, sit at the right height and mount securely to the trailer frame. This guide walks you through measuring your wheel and tire, choosing a fender style, and fitting it so spray and road debris stay off your boat and your lights.
Measure Your Wheel and Tire Before You Buy
A 13 inch wheel is only the rim diameter. The overall tire diameter is what sets the fender clearance, so measure the tire itself. Check the sidewall marking on the tire, which usually reads something like 175/70R13, and note the tire width in millimeters. A wider tire needs a wider fender opening.
Shopping for one? See our guide: 6 Best Anchor Balls for Boats: Buoys and Fenders Compared (2026).
Next, measure the gap between the top of the tire and the trailer frame or wheel well. Leave at least an inch of clearance so the fender does not rub when the trailer bounces over ruts. Measure the width of the tire at its widest point, then add room for the fender lip and a little side clearance.
Choose the Right Fender Style
Most trailer fenders fall into two groups: bolt-on fenders that attach to the frame with brackets, and clamp-on or strap-on fenders that wrap around an existing crossmember. Bolt-on types hold their position better on rough roads. Clamp-on types are easier to remove for tire changes.
Material matters too. Polyethylene and other molded plastics resist salt and UV. Galvanized or powder-coated steel handles heavier loads and gravel impact but needs rust checks. Match the material to where you launch: saltwater launches favor plastic or coated metal.
Fit the Fenders Step by Step
- Park the trailer on level ground and chock the wheels.
- Mark the mounting points on the frame, centered over the tire with the clearance measurement you took earlier.
- Pre-drill holes only where the manufacturer’s instructions allow. Avoid drilling through structural welds or the axle.
- Install brackets loosely first, then position the fender and check that it clears the tire through a full turn of the wheel by hand.
- Tighten all fasteners and recheck clearance after a short test drive on bumpy pavement.
Recommended gear
A basic socket set and a torque wrench help you tighten mounting bolts evenly without cracking brackets. A tape measure with a clear millimeter scale makes the clearance checks quicker and more accurate. Stainless steel fasteners resist rust better than zinc-plated hardware on trailers that see water.
Common Mistakes to Avoid
- Measuring the rim instead of the tire, which leads to fenders that rub.
- Mounting fenders so low that road spray still reaches the hull.
- Drilling into the axle or structural welds.
- Skipping a recheck after the first few miles, when brackets often settle.
- Forgetting that fenders can block trailer lights; keep wiring and reflectors visible.
For a broader look at fender choices and placement, see Fenders for Boat Trailer: How to Choose and Fit Them (Step-by-Step) and How Do Boat Fenders Work? Cushioning, Placement and Sizing Explained. If your hub area is also leaking or wearing, Why Is My Boat Trailer Hub Cover Leaking? 6 Causes and Fixes covers those issues.
FAQ
Can I use the same fenders for 13 inch wheels and larger sizes?
Not always. Fenders are sized to the tire width and diameter, so a fender built for a 13 inch setup may not clear a larger tire. Check the manufacturer’s listed tire size before buying.
How much clearance should there be above the tire?
Aim for at least one inch between the top of the tire and the fender at its lowest point on the bumps. This gives room for the trailer to flex without contact.
Do trailer fenders need to be removed for launching?
Usually no, since they are mounted above the wheel. However, check that they do not interfere with bunks or the winch post. Consult your trailer manufacturer if you are unsure about fitment with your specific setup.
Conclusion
Measure the tire, not just the rim, and leave clearance for flex and bounce. Choose a material that suits your launch water, mount the fenders firmly, and recheck after the first drive. Done this way, your trailer fenders will do their job for many seasons.
Related reading
Ready to choose one?
