How to Measure Boat for Cover: A Step-by-Step Guide for Accurate Fit
Learn how to measure boat for cover with a simple step-by-step method covering length, beam, height and fit, so your cover goes on snug and stays put.
Updated November 2026
Learning how to measure boat for cover takes about fifteen minutes and a tape measure. You will record the length, beam and height your cover needs, plus the extra allowances that keep it from tearing, pooling water or flapping in the wind. Measure once carefully, then compare your numbers against the manufacturer’s sizing chart before you order.
Gather Your Tools and Prepare the Boat
Use a flexible cloth or fiberglass tape rather than a rigid steel tape, since the tape has to follow the curve of the hull. Clear the deck of loose gear, remove the bimini top if you plan to leave it in place only if your cover is designed to fit over it, and park the boat on level ground so your readings are not skewed by a tilted hull.
Shopping for one? See our guide: Seal Skin Boat Cover Review: Is It Worth It? (2026).
- Flexible tape measure, at least 25 feet long
- Notepad or phone for recording figures
- Helper for holding the far end of the tape
- Your trailer or rigging details, if the cover must fit over them
Measure Length, Beam and Height
Most covers are sized from three core dimensions. Take each one at the widest or longest point, not the nominal listing for the model.
- Overall length: Run the tape from the tip of the bow to the farthest point at the stern, including the motor or swim platform if the cover must reach it. Record the figure to the nearest inch.
- Beam (width): Measure across the widest part of the hull, usually at the gunwales or the pontoon tubes. Include any flared sides or rub rails that stick out.
- Height: Measure from the waterline or deck to the highest point you want covered, such as the console, T-top or windshield. Take a second reading at the bow if your boat has a raised bow profile.
Add Allowances for a Proper Fit
Do not order a cover that matches your raw measurements exactly. Covers need room to breathe and to shed water. Many manufacturers recommend adding a few inches to length and width, and a bit more height if the boat carries a large console or T-top. Check the specific allowance in the sizing guide for the cover brand you are buying, since these figures vary by design.
Check Your Measurements Against the Sizing Chart
Match your numbers to the chart by boat length and beam, then confirm height and any special features. The table below shows the dimensions to record so nothing gets missed.
| Dimension | Where to Measure | Common Mistake |
|---|---|---|
| Length | Bow tip to stern or motor | Using the listed model length |
| Beam | Widest point of the hull | Measuring inside the gunwales |
| Height | Deck or waterline to highest accessory | Forgetting the T-top or console |
| Trailer | Tongue to rear axle, if covered | Ignoring trailer-mounted equipment |
If your measurements fall between two sizes, choose the larger size. A cover that is slightly loose is easier to tighten than one that is too short to close.
Common Mistakes to Avoid
- Measuring the trailer and boat separately and forgetting to add the tongue length.
- Recording the boat’s advertised length instead of the actual measured length.
- Skipping the height reading, which leads to a cover that sags over the console.
- Measuring on uneven ground, which distorts every figure.
- Ignoring outboard motors, swim platforms and bow rails that need clearance.
Recommended Gear
A flexible fiberglass tape is the single most useful tool for this job because it follows the hull curve without bending the reading. A second person holding the far end keeps the tape straight and taut, which improves accuracy.
- Fiberglass tape measure: Flexes around the hull and gives consistent readings across long runs. View on Amazon
- Marking tape or painter’s tape: Marks reference points on the hull so you can repeat measurements. View on Amazon
FAQ
Should I measure the boat with the outboard or trailer attached?
Measure with everything attached that the cover needs to fit over or around. If the cover goes over the motor, include it in the length; if it stays off the motor, measure without it.
How much extra room should I allow?
Allowances differ by brand, so follow the manufacturer’s sizing guide. Extra room is usually added to length, width and height so the cover does not stretch or trap water.
What if my boat has an unusual shape?
Take extra readings at each change in profile, such as the bow, console and stern, and send them to the manufacturer. Many companies offer custom sizing when standard charts do not fit.
Conclusion
Measure the length, beam and height at their widest or highest points, then add the allowance the manufacturer recommends. Compare your figures to the sizing chart, and choose the larger size when you fall between two. Accurate measurements now mean a cover that fits well and protects the boat for seasons to come.
Related reading
- West Marine Boat Cover: How to Choose, Measure and Fit One (7 Steps)
- Vinyl Boat Seat Cover: How to Measure, Fit and Protect Your Seats
- V Hull Boat Cover: How to Measure, Choose and Fit One (2026)
- Truxedo Boat Windshield Cover: How to Choose, Measure and Fit One
Ready to choose one?
