22ft Pontoon Boat Cover: How to Measure, Choose and Fit One (2026)
Learn how to measure, choose and fit a 22ft pontoon boat cover, with tips on material, sizing, support and care so your boat stays dry all season.
Updated November 2026
A 22ft pontoon boat cover keeps rain, UV rays, dust and debris off your deck, furniture and electronics when the boat is docked or stored. This guide walks you through measuring your boat correctly, choosing a material and style that fit your conditions, and getting a snug, well-supported fit. Get these steps right and the cover will last longer and protect more.
Measure Your 22ft Pontoon Before You Shop
Most 22ft pontoon boats fall roughly in the 22 to 24 foot overall length range, so do not assume the listed size is the size you need. Measure the boat yourself and write the numbers down before comparing covers.
Shopping for one? See our guide: 6 Best Seat Covers for Pontoon Boat (2026): Picks Compared.
- Measure overall length from the bow tip to the stern, including any swim platform or ladder that the cover must go over.
- Measure beam (width) at the widest point of the pontoons, usually across the deck rails.
- Measure height from the waterline or deck to the highest point you want covered, such as the top of the bimini frame or console.
- Note whether you have a bimini top, T-top or a console, because these change the cover shape.
Manufacturers usually list cover sizes by length and beam ranges. Choose the range that covers your measurements, and if you fall between two sizes, pick the larger one for a looser fit with room for the frame.
Choose Material and Style for Your Conditions
Marine-grade vinyl and solution-dyed polyester are the two materials you will see most often. Vinyl sheds water well and resists mildew when kept dry, while polyester breathes better and handles UV exposure for many seasons. If you store the boat in strong sun, look for UV-resistant fabric, and if humidity is high, prioritize breathability to reduce trapped moisture.
Style matters as much as material. A full cover wraps the entire boat and gives the best protection, while a mooring or bimini-style cover protects the top and leaves the sides open for airflow. Full covers suit winter storage. Mooring covers suit short-term protection while you use the boat between trips.
Fit the Cover and Set Up Support
A cover that sags will collect water and wear faster at the contact points. Setting up a support system keeps the fabric above the deck so rain runs off instead of pooling.
Basic Fitting Steps
- Lay the cover over the boat with the seams centered and the front end pointing toward the bow.
- Fasten the snaps or straps at the stern first, then work forward on each side.
- Tighten the bow tie-downs so the cover lies flat without bunching.
- Check that the cover clears the bimini frame, railings and any antennas by at least a few inches.
Add Support Poles or Frame
For a 22ft boat, a pole or frame system in the middle and at each end holds the cover off the deck and carries snow or standing water. Position poles where the fabric naturally peaks, and check that each pole sits square and does not press through the material.
Common Mistakes to Avoid
- Buying by the advertised boat length alone instead of checking your own measurements.
- Covering a wet boat, which traps moisture and encourages mildew under the fabric.
- Skipping support poles, which allows water and snow to sag the cover and tear seams.
- Leaving snaps or straps loose in wind, causing the cover to flap and chafe the finish.
- Ignoring ventilation, so condensation builds up inside the cover over long storage periods.
Recommended Gear
- Adjustable cover support pole set: Holds the fabric off the deck so water runs off and does not pool. View on Amazon
- Marine-grade cover cleaner: Removes dirt and mildew from fabric without stripping water repellency. View on Amazon
- Heavy-duty cover straps and tie-downs: Secure the cover at the bow and stern so wind cannot lift the edges. View on Amazon
For more on setting up support and storage, see Pontoon Boat Cover Support System: How to Set One Up (Step-by-Step) and Winter Cover for Pontoon Boat: A Step-by-Step Guide for Beginners.
FAQ
How do I know if a 22ft pontoon boat cover will fit?
Measure overall length, beam and height including any bimini or console, then compare those numbers to the size chart. If your measurements fall between two sizes, choose the larger one.
Should I use a full cover or a mooring cover?
A full cover suits long-term winter storage, while a mooring or bimini-style cover works better for short-term protection with airflow. Match the choice to how long the boat will sit.
Do I need support poles for a 22ft pontoon cover?
Support poles are strongly recommended because they keep the fabric off the deck so water and snow do not collect and stress the seams.
Conclusion
Measure your boat carefully, choose a material and style that suit your storage conditions, and fit the cover with proper support. Following these steps gives you a dry, protected boat and a cover that lasts longer. Check manufacturer sizing and fitting instructions before you buy.
Related reading
- Waterproof Pontoon Boat Cover: How to Choose, Fit and Keep It Dry (2026)
- Universal Pontoon Boat Cover: 3 Best Picks Compared (2026)
- Top 3 Pontoon Boat Shade Cover Picks for Sun Protection (2026)
- Top 3 Pontoon Boat Covers for Sale Picks for Every Fit (2026)
Ready to choose one?
