We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Boat Cover Fleet Farm: How to Choose, Measure and Fit One (2026)

Looking for a boat cover at Fleet Farm? Learn how to pick the right size and material, measure correctly and fit it so it stays dry all season.

Updated November 2026

A boat cover from Fleet Farm can protect your hull, upholstery and electronics from rain, snow and UV damage when it is the right size and fitted properly. This guide walks you through choosing the right boat cover Fleet Farm stocks, measuring your boat accurately, and securing it so it stays put through wind and weather. Most fit problems come down to measurements taken in the wrong place, so take your time with that step.

Step 1: Measure Your Boat Correctly

Measure length from the bow tip to the stern, then add a few inches for a snug finish. Width should be taken at the widest beam point, and height from the deck to the top of the highest fixed item, such as a console, windshield or T-top. For pontoon boats, measure the length of the deck and add the allowance for the rails. Compare your figures against the size chart on the product page rather than relying on the boat’s listed length alone, since a 16-foot boat with a motor and bow rail may need a different size.

Shopping for one? See our guide: Seal Skin Boat Cover Review: Is It Worth It? (2026).

Step 2: Choose a Material That Suits Your Storage Conditions

Fleet Farm carries cover fabrics in several weights, and each suits different conditions. Lightweight polyester works well for dry, indoor-adjacent storage. Heavier coated polyester or vinyl-coated fabrics handle rain and snow better, but they can trap moisture if the cover is not ventilated. If you plan to leave the boat outdoors year-round, look for UV-resistant fabric and built-in vents. For more detail on fabric performance, see Waterproof Boat Cover Material: Which Fabric Keeps Water Out Best?.

Step 3: Fit and Secure the Cover

Place the cover over the boat with the front centered on the bow, then pull the rear down evenly. Tighten the bow and stern straps, then the side tie-downs, working from the center outward. Use straps or cable ties at the trailer hitch and around any loose areas to stop wind lift. Where the cover has an open span, such as over a windshield or bimini, a support frame keeps water from pooling. The guide on Supports for Boat Cover: How to Choose and Install the Right Ones (2026) explains how to set these up.

Step 4: Plan for Airflow and Moisture Control

Trapped moisture causes mildew and corrosion faster than sun or rain. Leave the cover slightly loose at the sides so air can circulate, and use vents on the cover if it has them. Check the cover after heavy rain or snow and brush off accumulated weight. If you want to compare vent options, Top 7 Vents for Boat Cover Picks Compared: Airflow and Moisture Control covers the choices in detail.

Checklist before you finish

  1. Confirm length, beam and height against the size chart.
  2. Choose a fabric rated for your climate and storage setup.
  3. Position the cover with the bow centered.
  4. Tighten bow, stern and side straps evenly.
  5. Add a support frame if the cover sags over open areas.
  6. Check for pooled water and loose straps after each storm.

Common Mistakes to Avoid

  • Buying by boat length alone and ignoring height and motor or rail add-ons.
  • Pulling the cover tight without leaving room for airflow, which traps condensation.
  • Skipping straps at the trailer hitch, where wind lift usually starts.
  • Letting snow or standing water build up on top of the cover.
  • Storing a damp cover, which encourages mildew on the fabric.

A cover support system keeps the fabric from collecting water over the console or windshield. View on Amazon

Stainless snap fasteners and tie-down straps make it easier to secure the cover tightly without loosening over time. View on Amazon

FAQ

Is a Fleet Farm boat cover waterproof?

Most covers sold at Fleet Farm are water-resistant rather than fully waterproof. Heavier coated fabrics shed rain well, but seams and vents can still let moisture in, so check the product description for the specific fabric rating.

How do I know which size to buy?

Measure length, beam and height at the boat’s widest and tallest points, then match those numbers to the manufacturer’s size chart. If your measurements fall between two sizes, choose the larger one for a better fit.

Can I leave a boat cover on all year?

You can, provided the cover is well fitted, vented and kept clear of standing water and heavy snow. Check it regularly and dry the boat and cover before long storage periods. Consult your boat or cover manufacturer for climate-specific guidance.

Conclusion

Choosing a boat cover from Fleet Farm comes down to accurate measurements, a fabric suited to your climate and a secure, ventilated fit. Follow the steps above, and check the cover after severe weather to keep your boat protected all season.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our houseboating guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Discover Houseboating.